用AT89C51单片机实现四位数码管显示数据！！用c语言程序实现！！例如显

用AT89C51单片机实现四位数码管显示数据！！用c语言程序实现！！例如显示出0412 这四个数。请各位朋友帮忙

第1个回答 2017-05-05

#include<reg51.h>
#define uchar unsigned char
uchar tab[]={0x3f,0x06,0x5b,0x4f,0x66,0x6d,0x7d,0x07,0x7f,0x6f,0x00}; //0到9
uchar num;
uchar led[]={0,4,1,2};
void t0isr() interrupt 1
{
TH0=(65536-5000)/256;
TL0=(65536-5000)%256;
switch(num)
{
case 0:P2=0x01;break;
case 1:P2=0x02;break;
case 2:P2=0x04;break;
case 3:P2=0x08;break;
default:break;
}
P0=~tab[led[num]];
num++;
num&=0x03;
}
main()
{
TMOD=0x11;
TH0=(65536-5000)/256;
TL0=(65536-5000)%256;
TR0=1;
ET0=1;
EA=1;
while(1);
}本回答被网友采纳

相似回答

用AT89C51单片机实现四位数码管显示数据!!用c语言程序实现!!例如显示...答：//显示567- for(d = 0;d<20;d++){

AT89C51单片机60.00到00.00倒计时程序 4位数码管显示 C语...答：ncludereg52.h> define uchar unsigned char define uint unsigned int uchar num,t;sbit dula=P2^6; //段选跟位选 sbit wela=P2^7;uchar code table[]={0x3f,0x06,0x5b,0x4f,0x66,0x6d,0x7d,0x07,0x7f,0x6f}; //共阴数码管 void display(uchar b,uchar a);void delay1ms()...

AT89C51单片机怎么用汇编语言让4个数码管同时显示1234?答：1、首先我们先打开keil。2、接着，我们要定义好库函数，void main(){while(1)//不断循环显示{dispaly();}}void dispaly(){P0=smg[1];//选择显示数字几，P1=0x7f;//控制是否点亮数码管。3、接着，我们加上一条循环语句。delay(5);//显示5毫秒P0=0XFF;//消影P0=smg[2];P1=0xbf;delay...

AT89C51与四片74HC595跟四个数码管连接的显示程序怎么写啊?用C语言...答：sbit DS = P1^3;uchar temp[10]= {0x3f,0x06,0x5b,0x4f,0x66,0x6d,0x7d,0x07,0x7f,0x6f};uchar table[4];void delay(uint time){ while(time--);} void write_595a(uchar date){ uchar i;for(i = 0;i < 8;i++){ SCK = 0;DS = date & 0x80;SCK = 1;date <<= ...

AT89C51单片机实现4位数码管显示学号后四位,谢谢答：void display()//4位显示子程序 { P0=~(table[ table2[0]]);wei1=0;Delay1ms(2);wei1=1;P0=~(0x80|table[ table2[1]]);wei2=0;Delay1ms(2);wei2=1;P0=~(table[ table2[2]]);wei3=0;Delay1ms(2);wei3=1;P0=~(table[ table2[3]);wei4=0;Delay1ms(2);wei4=1;} ...

用AT89C51单片机,4位共阴极数码管,显示出1234 程序怎么写??? 请各位...答：MOV 32H,#02H MOV 33H,#03H MOV 34H,#04H MOV 35H,#05H MOV 36H,#06H ACALL D0 JMP $-2 D0: MOV R0,#31H MOV R2,#11111110B MOV DPTR,#TAB D1: ORL P1,#00111111B MOV A,@R0 MOVC A,@A+DPTR MOV R3,#8 D2: RLC A MOV...

求C语言程序,AT89C51单片机为核心,DS18B20测温度,实时用4位LED显示...答：include<reg52.h> // 试试#define uchar unsigned char #define uint unsigned int sbit DQ=P1^4; //ds18b20与单片机连接口 unsigned char code str[]={0x3f,0x06,0x5b,0x4f,0x66,0x6d,0x7d,0x07,0x7f,0x6f,0x00,0x40} ; //共阴数码管字码表unsigned char code str1[]={0...

AT89C51单片机用4位数码管做秒表,要求用动态扫描做,汇编语言答：;汇编时钟程序。4位共阳管。P0口段码，P2.0~P2.3位码。显示毫秒和秒。三个按键一个控制时钟开始走，一个控制暂停和继续。。。一个按键清0 ;12M晶振 2011 04 20 调试完成 STRT EQU P3.2 STP EQU P3.3 CLRR EQU P3.5 ORG 00H SJMP MAIN ORG 0BH AJMP T0INT ORG 30H MAIN: MOV ...

大家正在搜